| Author
|
Yhtiot - Universe Of Nothing
|
Hare
IsraTrance Junior Member
Started Topics :
22
Posts :
119
Posted : Apr 21, 2012 19:26:28
|
Yhtiot — Universe Of Nothing
1. Peikon Synttärit (8:39)
2. Minä Unelmoin Sinusta (7:57)
3. The Lament Of Tujaarma Kuo (6:40)
4. Metsän Lapset (6:31)
5. Udmurtian Partyvan (6:14)
6. Native Speaker (6:30)
7. Universe Of Nothing (7:53)
8. Poroscaner (6:26)
9. Jurriset Pöllöt (5:32)
10. Death Signs (7:48)
OUT NOW! @ equaldreams.com
en.equaldreams.com/feeless
en.equaldreams.com/yhtiotpineharmonix
  http://www.antiscarp.com |
|
|
|
Hare
IsraTrance Junior Member
Started Topics :
22
Posts :
119
Posted : Apr 28, 2012 09:48
|
All tracks written by Konstantin Yhtiot at different places and in various conditions.
Mastering by Max Laine @ Wolfborder Studios, Finland
Produced by Feeless Records, Russia
http://www.antiscarp.com |
|
|
|
shenlaizai
Started Topics :
0
Posts :
23
Posted : Feb 25, 2013 08:58
|
Remove the valve cap and fully deflate the tube by[url=http://www.icarbonsports.com/products/wheels-rims/carbon-bike-rims/]carbon bike rims[/url] depressing the valve stem with the hooked end of your tire lever. There are two main types of valve stems, a schrader valve and a presta valve. This tutorial is based on a schrader valve, but I will be covering the different valve types in another tutorial.
Now it¡¯s time to remove your tire, one side at a time. Choose a section of tire that is away from the valve and hook one of the tire levers under the bead, directly in line with one of your spokes. Pry one side of the tire bead over the edge of the rim, and then hook the end of the tire lever to the nearest spoke. Insert another tire lever two spokes away from the first, and a third another two spokes away. Now the middle lever should fall out, and you can continue the process. When the tire is loose enough you can just run a tire lever around the rest of the rim to pull the whole side over.
After you have removed one side of [url=http://www.icarbonsports.com/products/wheels-rims/carbon-bike-rims/]carbon fiber rims[/url] the tire, the other side should come off very easily.
Inspect Tube
Now remove the tube from the tire, and try to keep [url=http://www.icarbonsports.com/products/wheels-rims/carbon-bike-rims/]carbon bicycle rims[/url]track of where it was positioned in relation to the tire. Inflate the tube to approximately twice its original size. This will expand the hole making it easier to find.
Listen carefully to the entire circumferenceof the tube; you should hear a hissing sound that will indicate where the leak is. As a last resort you can submerge the tube in water and watch for bubbles, but you¡¯ll want to avoid doing this as you¡¯ll need the tube to be completely dry in order for the patch glue to work.
Once you¡¯ve found the leak, take note of whether it is on the inner or outer side of the tube.
If the hole was on the outer side of the tube, inspect the inner surface of the tire in that spot to make sure the object that caused the puncture is not still stuck in the tire. Double check the entire inner side of the tire by running your fingers along the entire surface, feeling for obstacles along the way.
If the hole was on the inner side of the tube,inspect your [url=http://www.icarbonsports.com/]zipp 404[/url]entire rim to make sure there are no sharp burrs in the metal, and that the rim tape is properly protecting the tube from your spoke ends.
Now that the rim and tire are clear, it¡¯s time to patch the tube. Select an appropriate sized patch for the hole. Use the sandpaper or scraper provided in your kit to buff the surface of the tube for an area a bit larger than the patch. You need to buff the tube so that it is no longer shiny. If the molding line is running along the area where the patch is to be applied, you must sand it down completely, or it will provide an air channel. Once buffed, avoid touching that area with your fingers.
Apply a dab of rubber cement, and then spread it into a thin coat, using your cleanest finger. Work quickly. You want a thin, smooth coat of cement; if you keep fiddling with it as it begins to dry, you¡¯ll risk making it lumpy. The thinner the cement, the faster it will dry. It is very important to allow the cement to dry completely.
Peel the foil from the patch and press the patch onto the tube firmly, squeezing the patch tightly onto the tube.
|
|
|
|
|
