| Author
|
Virus TI Snow > Not In Tune With Other VST's / Hardware
|
Pypedream
IsraTrance Junior Member
Started Topics :
45
Posts :
245
Posted : Jun 25, 2009 05:12:13
|
Either it's the Virus, or all of my other synths are out of tune.
When I get some chords or melody going in the project and then call up the Virus to add a layer, playing the same chords sounds severely out of tune. I've checked the global settings to make sure everything is equalized - and it is. So now I'm really lost.
I suppose I could tune the oscillators to the rest of my sounds but no way I want to do this every time I'm auditioning a preset.
Am I missing something here? Checked the Forums and boards and couldn't find much.
How about sending audio from a buss (Cubase) to the TI effects - would you have to use a physical send / return line or should it work through the same USB link that is carrying audio from the synth to the PC? If I can't get the tuning issue solved at least I should use the effects hehe.
  ELECTRON EYES / MARK-EVAN (NOR. CAL)
WWW.SOUNDCLOUD.COM/MARK-EVAN |
|
|
|
realtime
Started Topics :
5
Posts :
350
Posted : Jun 25, 2009 08:14
|
Quote:
|
On 2009-06-25 05:12:13, Pypedream wrote:
When I get some chords or melody going in the project and then call up the Virus to add a layer, playing the same chords sounds severely out of tune. I've checked the global settings to make sure everything is equalized - and it is. So now I'm really lost.
I suppose I could tune the oscillators to the rest of my sounds but no way I want to do this every time I'm auditioning a preset.
|
|
check if master tuning is 440Hz (or 432Hz)
and also check the OSC phase init (0 = free running oscillator)
Quote:
|
On 2009-06-25 05:12:13, Pypedream wrote:
How about sending audio from a buss (Cubase) to the TI effects - would you have to use a physical send / return line or should it work through the same USB link that is carrying audio from the synth to the PC? If I can't get the tuning issue solved at least I should use the effects hehe.
|
|
not sure about the snow - in virus control ... check the common tab ... there you can setup how many inputs/outputs.
did you flash the TIOS to v3.0.3.00 final yet?? http://www.myspace.com/realtimeproject |
|
|
|
Axis Mundi
Axis Mundi
Started Topics :
75
Posts :
1848
Posted : Jun 25, 2009 19:05
|
I haven't ever experienced this problem, but here's what you can try.
1.) Turn off the Snow and unplug ALL cables from it.
2.) Wait 30 secs.
3.) While holding down the EXIT button, plug the power cable into the Snow. When it says "USB Update Mode" on the screen, you can let go of the button.
4.) Re-install the software suite and follow the instructions it gives you.
Let me know if that works.
Here's another website you can try to for help, by the way.
http://www.infekted.org
|
|
|
|
realtime
Started Topics :
5
Posts :
350
Posted : Jun 25, 2009 20:06
|
|
vafl
Started Topics :
2
Posts :
36
Posted : Jul 7, 2009 15:24
|
i had similiar problem on Ti snow. it was due low latency set on the RME sound card rising it to 3ms fixed mine problem.
everyone want near zero hehe but sometimes it doesen't work 
@realtime
check if master tuning is 440Hz (or 432Hz)
--.
u need to do it by hand on virus front panel, this option is not in vsti gui. |
|
|
|
Raoul V
IsraTrance Junior Member
Started Topics :
26
Posts :
583
Posted : Jul 31, 2009 11:59
|
|
i had this occur once when using my snow... for eg when i played an A note it was playing a A#, i just rebooted and all was good... |
|
|
|
