| Author
|
Good ressource for learning synthesis?
|
Upavas
Upavas
Started Topics :
150
Posts :
3315
Posted : Dec 12, 2008 03:16
|
|
PsyTiax
IsraTrance Junior Member
Started Topics :
26
Posts :
190
Posted : Dec 12, 2008 10:15
|
Thanks for all your answers guys  |
|
|
Magus
IsraTrance Junior Member
Started Topics :
22
Posts :
61
Posted : May 27, 2009 21:08
|
Quote:
|
On 2008-12-11 16:10, makus wrote:
its also useful to read synth manual. i remeber when i first read z3ta's manual i found out many new things
|
|
Possible to upload the manual? been trying to get that one, but with no luck. |
|
|
|
Upavas
Upavas
Started Topics :
150
Posts :
3315
Posted : May 27, 2009 21:52
|
Here is an Albino tutorial that was posted sometime ago in Isra, might help...
1. analong oscillation: switch osc1 to analog mode and twist its waveform dial right around to the triangle wave and set the pulse width (symmetry) to around half way, so its still a bit thin. tune it down one octave and push the fm mode.
2. wave mix: enable osc2, flip it to digital and set the start end waveform to spectr13)16") and sawbass3 (8") respectively. move the mix slider so it has a bias toward the spectrum wavform and then switch the oscillator to route though both filters.
3. creamy filters: for a classic warm analog squidge, set filter1 to cream and the tope to 24db per octave lowpass. turn the cutoff frequency dial down to around 4681hz and crank up the resonance to 83. turn down the env control to 0.70.
4. shapely filters: head off to the envelope section and push f1 to access the envelope for the first filter. to create a nice sweeping filter bass, make sure the attack is set to 0.001 and then turn the decay to around 0.5. all the other dials can be set to 0.
5. silky sounds: in the filter banks, switch the 2nd filter to silk and set its type to bandpass. this will alter its tonality, especially with the resonance turned up full. adjust the cutoff frequency to around 2419hz and turn up the saturation to until you get a nasal tone.
6. lfo's: here where it starts to get fun. flip open lfo1 and set its waveform to random. turn the symmetry and phase dials to 71 and 27 respectively. rather then use the frequency to set the lfo speed, click on the sync box and set it to 1/2 steps.
7. map the mod: press mx to access the mod matrix. click on the left hand column and pick lf1 from the menu, then choose the cutoff filter2 as the target with a depth of 0.4. do the same with the 2nd row, setting the target to resonance filt2, set the depth to -0.3
8. arperggiate it: with the waveform wobbling, start the arp to reign on it. push the ap button, set its mode to up/down+ and the step time to 1/16. make the note length just a little longer, so that it only spans 1 octave. set the 16-step pattern to: 118,tie,056,046,071,088,off,100,126,tie,065,035,off,100,off,100.(this is just an example)
9. apply fx: to get distortion going set the first fx to to flanger and the 2nd to another bandpass filter. on the filter try to adjust the saturation to 94 and the dry/wet balance to 72. set the cutoff and resonance controlce to 1369hz and 46 respectively.
Reply
Forward
 Upavas - Here And Now (Sangoma Rec.) new EP out Oct.29th, get it here:
http://timecode.bandcamp.com
http://upavas.com
http://soundcloud.com/upavas-1/ |
|
|
|
jizy
IsraTrance Full Member
Started Topics :
90
Posts :
1493
Posted : May 27, 2009 23:22
|
|
great recource? a synth prehaps?
|
|
|
|
|
