| Author
|
Cuabse Sx 2 PRoblem ... PLs hlp !!!
|
WAVELOGIX
Wavelogix
Started Topics :
136
Posts :
1214
Posted : Jan 14, 2004 22:30
|
hi guys ,
i hope all u ppl doing 5n 
ok here is my problem in cubase sx 2
i draw notes in midi tracks using the key editor..
after lets say i draw a 2 bar pattern , i press ctrl+d [ duplicate ] to repeat the pattern as long as i want to ..
but now the problem is tht as i keep on duplicating , the fruther notes , keep getting shifted a lil here and there , and i have to keep adjusting them all the time to get them back into meter !!!
do u ppl also face the same problem ..
pls hlp me out wid ths
bye and take care ..
  http://www.youtube.com/watch?v=CTPJuMSwzUQ |
|
|
|
Anak
Anakoluth
Started Topics :
108
Posts :
2395
Posted : Jan 15, 2004 11:14
|
|
billy ambulance
IsraTrance Junior Member
Started Topics :
43
Posts :
560
Posted : Jan 15, 2004 11:35
|
|
WAVELOGIX
Wavelogix
Started Topics :
136
Posts :
1214
Posted : Jan 15, 2004 12:32
|
hey ppl , thanks for your hlp and support
but i luckily was messing around and found the answer to the problem ...
all i had to do was to go to midi -> quatize seup and check the auto option and im set
thanks newys ...
bye and take care ... |
|
|
|
Colin OOOD
Moderator
Started Topics :
95
Posts :
5380
Posted : Jan 18, 2004 21:52
|
If you draw notes in the MIDI editor and then duplicate the part, the notes in the new parts should end up exactly in the right place.
It sounds like your part is just a little longer than a bar. This can happen if you draw in a note which ends after the end of the part - you get a dialog up asking "Extend part?"; if you answer Yes then the part is lengthened to include the end of this last note.
Any duplicates (which get placed right up against the edge of the previous part) will then not start exactly on the bar any more and any notes inside them will be shifted to one side.
Answering No to "Extend part?" will stop this from happening and will not chop off the end of your last note.
If you want to check whether your part is too long, look at the Object Details with the original part selected. The part's 'end' field should look something like "25.1.1.0" |
|
|
|
WAVELOGIX
Wavelogix
Started Topics :
136
Posts :
1214
Posted : Jan 21, 2004 22:13
|
colin , i get tht extend part question when i try to adjust the note that has moved off qunatization , whcih i answer as no ...
and i draw proper 1 bar loops with grid mode set to bar ...
even pasting the parts over nad over agin does the same thing ....
some of the notes move out of the respective quantization ...
i thkn there is some quantization setting that i havent set properly 
i even went to midi - advanced quantize- and checked that atuo box , but of no avail
pls hlp mw out guys ... im also trying
|
|
|
|
Colin OOOD
Moderator
Started Topics :
95
Posts :
5380
Posted : Jan 21, 2004 23:39
|
You sure you have Snap on when you draw your parts? (the button that looks like ">|<")
If SX asks you if you want to extend the part when you try to adjust the note it sounds very much as if the part is too short. Make sure the start and end of the part are both 'x.1.1.0' before you duplicate it.
Does it still happen if you copy the part by holding <alt> down and moving it?
|
|
|
|
WAVELOGIX
Wavelogix
Started Topics :
136
Posts :
1214
Posted : Jan 22, 2004 12:13
|
I TRIED BY COPYING THE PART WITH HOLDING DOWN THE ALT BUTTON AND IT WORKS JUST 5N
I GUESS DUPLICATE HAS ANOTHER BUG ATTACHED TO IT IN CUBASE SX 2 ..
BTW IS LOGIC REALLY BETTER THAN SX2 ??
I COULD TRY OUT THT ALSO ... |
|
|
|
Colin OOOD
Moderator
Started Topics :
95
Posts :
5380
Posted : Jan 23, 2004 03:03
|
I use duplicate with no problems. I still reckon your parts are not an exact number of bars long!
Logic and SX2 are roughly equivalent; each has advantages over the other in different areas. If you use a PC I'd recommend you use SX though, as this has an upgrade path and is still under development, whereas Logic on a PC will forever remain at v5.5.1.
|
|
|
|
